Access to information is restricted depending on your login. Request login-information through our contact form.


Audio (UCB1400)

This describes the audio-driver for the UCB1400-codec found on the Trizeps-module.

Registry Keys

Key Type Description
MuteMode DWORD How to mute the device during no audio ouput. (see Mute Settings)
MutePortAdr DWORD Address to write to, if MUTE_PORTADR is used. (see Mute Settings)
MutePortSize DWORD Bus-width, if MUTE_PORTADR is used. (see Mute Settings)
MutePortMute DWORD Value to write for mute, if MUTE_PORTADR is used. (see Mute Settings)
MutePortUnMute DWORD Value to write for unmute, if MUTE_PORTADR is used. (see Mute Settings)
MuteGPIOPin DWORD GPIO-Pin to use, if MUTE_GPIOPIN is used. (see Mute Settings)
BassTreble DWORD Value to use for CSR1 register of UCB1400
Priority256 DWORD priority used for driver-threads
InputSource DWORD Source of audio-input: 1: MIC, 2: LINE_IN
CaptureLatency DWORD Capture-buffer-size in milliseconds. When using VOIP-applications, reducing capture-latency might be wanted.
PlayLatency DWORD Play-buffer-size in milliseconds. When using VOIP-applications, reducing play-latency might be wanted.
RecordGain DWORD See Record Gain Register (0x1C) of UCB1400-codec. Bits 0..7 are the gain setting for the right channel; bits 8..15 for the left channel.
MicVolume DWORD See MIC Volume Register (0x0E) of UCB1400-codec. Set bit 6 (0x40) to enable 20dB boost
WM9715ALC DWORD See ALC-Registers (0x60,0x62) of WM9715L-codec. The upper 16 bits are written to Reg60h, the lower to Reg62h. Default-value if not set is 0xB0323E00.
Key Type Description
Volume DWORD Volume: bits0..15 left channel; bits16..32 right channel

Mute Settings

There are many mute-modes availlable, which may be set through the MuteMode-registry key. The audio-output is unmuted and muted automatically before and after playing sound-files. Multiple mute-modes may be selected by setting the appropiate flags:

  • MUTE_HPEN (0x01)
  • MUTE_MASTER (0x02)
  • MUTE_VOLUME (0x04)
  • MUTE_DRVLIB (0x08)
  • MUTE_PORTADR (0x10)
  • MUTE_GPIOPIN (0x20)


Enable and disable headphone-driver.


Use master-mute bit in master-volume-register (0x02) of UCB1400.


Change volume for muting.


This calls a drvlib function to mute the device.
The drvlib writes to a board-control-register.


Write to register defined through MutePortAdr. MutePortAdr is a static virtual address.
MutePortSize can be 2 (16bit) or 4 (32bit) depending on the bus-width of MutePortAdr. MutePortMute is written to MutePortAdr if the device is muted. MutePortUnMute is written to MutePortAdr id the device is unmuted.


Toggles the gpio-pin given with MuteGPIOPin.
0V on gpio: device muted.
3.3V on gpio: device not muted.
If bit 0x100 is set in MuteGPIOPin, the logic is inversed.

Cookies helfen bei der Bereitstellung von Inhalten. Durch die Nutzung dieser Seiten erklären Sie sich damit einverstanden, dass Cookies auf Ihrem Rechner gespeichert werden. Weitere Information
service/wince/driversxscale/audio.txt · Zuletzt geändert: 2013/04/12 12:33 von